- 您现在的位置：买卖IC网 > Sheet目录629 > P1641100 (Red Lion Controls)P16 ANALOG CONTROLLER
6.0 P ROGRAMMING : H IDDEN L OOP
To enter Hidden Loop, press A for 3 seconds.
HIDDEN LOOP
Note: Parameters shown bold are the only parameters visible in the Hidden Loop with Factory Settings. Setpoint and Output Power are
factory set for the Display Loop. The remaining parameters can be selected for the Hidden Loop within Module 3.
Parameter availability is model and programming dependent.
240 °F
FRONTDISPLAY
TOP DISPLAY
TEMP/PROCESS
F1
ENDS AND RETURNS TO START OF DISPLAY LOOP.
BOTTOM DISPLAY
PARAMETER
SELECTION/VALUE
SPSL
SP-1
ADVANCES TO NEXT PARAMETER.
CHANGES SELECTION/VALUE.
???? ?
???? ?
???? ?
HIDDENLOOP
When A is pressed and held for three seconds, the controller advances to the
Hidden Loop. The Temperature/Process Value is shown in the top display. The
bottom display alternates between the parameter and its selection/value. B or
J is pressed to change the selection/value for the shown parameter. The new
selection/value is activated after A is pressed. When L is pressed, the
controller returns to the Display Loop and stores changed selection/values to
permanent memory. Hidden Loop parameters may be locked out in Lockout
Module ???? . Some parameters are model and programming dependent.
ACCESS CODE
1 to 12?
? ?
If the Access Code is set from 1 to 125, in Lockout Module ???? , Access
Code will appear here. By entering the proper Code, access to the Hidden Loop
is permitted. With the factory setting of 0, Access Code will not appear in the
Hidden Loop. A universal code of 111 can be entered to gain access,
independent of the programmed code number.
SETPOINT SELECT
??1 or ??2
? ??1
The SPSL function allows the operator to switch from or to, setpoint 1 and
setpoint 2. In the Display Loop, there is no annunciator indicating the selected
Setpoint, however, the selected Setpoint value is displayed and activated.
9
SETPOINT RAMP RATE
??? to ?????
? ???
The setpoint ramp rate can reduce sudden shock to the process and reduce
overshoot on startup or after setpoint changes, by ramping the setpoint at a
controlled rate. R annunciator flashes while ramping. With the T16, the ramp rate
is always in tenths of degrees per minute, regardless of the resolution chosen for
the process display. With the P16, the ramp rate is in least-significant (display
units) digits per minute. A value of 0.0 or 0 disables setpoint ramping. Once the
ramping setpoint reaches the target setpoint, the setpoint ramp rate disengages
until the setpoint is changed again. If the ramp value is changed during ramping,
the new ramp rate takes effect. If the setpoint is ramping prior to starting Auto-
Tune, the ramping is suspended during Auto-Tune and then resumed afterward.
Deviation and band alarms are relative to the target setpoint, not the ramping
setpoint. A slow process may not track the programmed setpoint rate. At power
up, the ramping setpoint is initialized at the ambient temperature/process value.
CONTROL MODE TRANSFER
??nF ? ???? ????
? ????
In Automatic Mode, the percentage of Output Power is automatically
determined by the controller. In Manual/User ???? Mode, the percentage of
Output Power is adjusted manually while in the Display Loop. The Control
Mode can also be transferred through the F1 Key or User Input. For more
information, see Control Mode Explanations.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
P1Z9ACR900W12
DIODE MOD PWR-BRIK DL 1200V 740A
PA3716
TOOL REPLACEMENT HEAD SET
PAXCDL10
ANALOG OUTPUT CARD
PAXLC800
COUNTER 8-DIGIT BI-DIR COUNT
PAXLPT00
METER PROCESS TIME 6-DIGIT
PAXLR000
METER RATE INDICATION 6-DIGIT
PB52233SLK
PROJ BOARD COLDFIRE M52
PD412411
DIODE MOD ISO DUAL 2400V 1100A
相关代理商/技术参数
P1641110
制造商:Red Lion Controls 功能描述:PROCESS CONTR, 1/16DIN DC ANALOG 2 ALRM 制造商:Red Lion Controls 功能描述:DC W/ANALOG OUT 2 ALARMS
P1-64121
制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Red Button 制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Momentary Contact Screw Panel Mount
P1-64122
功能描述:按钮开关 Style F Scrw LoLev Black Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64122W
制造商:OTTO 功能描述:Pushbutton Switches Style F Scrw LoLev Black Button 制造商:OTTO Engineering Inc 功能描述:STYLE F,SCREW,LOW
P1-64128
功能描述:按钮开关 Style F Scrw LoLev Gray Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64129
功能描述:按钮开关 Style F Scrw LoLev White Button
RoHS:否 制造商:OTTO 触点形式: 开关功能: 电流额定值: 电压额定值 AC: 电压额定值 DC: 功率额定值: 安装风格: 照明: 照明颜色: IP 等级: 端接类型: 触点电镀: 执行器: 盖颜色: 封装: 可燃性等级:
P1-64131
制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Screw Panel Mount
P1-64132
制造商:OTTO Engineering Inc 功能描述:Switch Push Button N.O. Round Button 10A 115VAC 28VDC Screw Panel Mount